Help centre

Lumo⁺ questions, answered

How to use it, safety, results and care, written from the Lumo+ user manual and our support team.

  • Session5 to 8 minutes
  • Weekly maximumAbout 15 to 25 minutes
  • Warranty2 years
EvenSkyn Lumo⁺ RF, EMS and red light skin tightening device

Using it

What is the maximum amount of time the Lumo⁺ can be used?

For the first two weeks, 5 to 8 minutes a week in total. After that, sessions of 5 to 8 minutes: one or two a week, at least three days apart, if you're under 40, or two or three a week, at least two days apart, if you're 40 or over. Never more than 25 minutes of RF time in a week.

These limits come from the Lumo+ user manual. They count every mode that runs RF, which is the first four: RF, Cleansing, Nourishing and Massaging. The Cool mode runs no RF and has no limit.

Weekly maximums from the manual's table:

  • Under 40: about 15 minutes on the face, or 20 minutes for face and neck, up to level 4.
  • 40 and over: about 20 minutes on the face, or 25 minutes for face and neck, up to level 5.

The manual also asks for at least 48 hours between low-intensity sessions, and says up to 7 to 10 days is ideal for the skin to fully recover. If in doubt, use the lower figure.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

How long per session can I treat the face, neck and décolletage?

Keep each session to 5 to 8 minutes of RF time and split it across the areas you treat. The weekly cap doesn't grow when you add areas: up to about 20 minutes a week for face and neck if you're under 40, or 25 minutes if you're 40 or over.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Which conductive medium should I use with the Lumo⁺?

Any water-based, oil-free product works: our conductive gel, a water-based serum, or a light mist of water. The manual says gel isn't required, but skin must be free of oils for the RF, Cleansing, Nourishing and Massaging modes. A highly conductive gel makes EMS feel stronger.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Can I use all the Lumo⁺ modes in one session?

Yes. Run them in the manual's order, RF, Cleansing, Nourishing, Massaging, then Cool, but keep the whole session to 5 to 8 minutes across the four modes that use RF. Cool uses no RF. Each mode also stops on its own timer, so a mode never runs longer than it should.

Cleansing can strip natural oils, so the manual suggests it every week or two at most, followed by moisturiser. For firming, spend most of the session in the RF and Massaging modes. Oil-based products can go on after the RF modes, before Cool.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

How is the Lumo⁺ temperature regulated?

A sensor in the head reads your skin throughout the session and, after a brief warm-up, holds it at about 40 to 42°C (104 to 107°F). That is also why the handset must keep moving: slow, constant motion spreads the warmth evenly. If it feels hot rather than warm, stop.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Can I use retinol or tretinoin with the Lumo⁺?

Not before a session: the RF modes need clean skin with only water or a water-based gel on it. Use retinoids on evenings when you don't use the Lumo+, and if your skin becomes irritated, pause both until it settles. With prescription tretinoin, ask your dermatologist.

Source: Lumo+ user manual; conservative EvenSkyn guidance. Reviewed November 2026

Was this helpful?

Can I use a high frequency wand alongside the Lumo⁺?

Yes, as long as your Lumo+ use stays within its own weekly limits. Go easy on cleansing: the Lumo+ Cleansing mode can strip natural oils, so the manual suggests it about every two weeks, followed by a moisturiser.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Safety

How do I use the Lumo⁺ safely?

Start on level 1 and step up only while it stays comfortable. Keep the handset moving slowly and never hold it in one spot. Stay within the weekly limits, keep it off the eyes, eyelids and the thyroid or Adam's apple, and stop if it feels hot rather than warm.

Before you start, read who shouldn't use it: the manual says the Lumo+ is not for children, pregnant women, people with metal implants anywhere in the body, or skin conditions that make RF or light unsuitable. Skin must be clean and free of oils for the RF, Cleansing, Nourishing and Massaging modes.

Stop and contact us if anything unusual happens, including extreme heat from the device, the charger or your skin.

Can I use it if: device-by-device safety

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Can I use the Lumo⁺ around my eyes?

Not on the eyes themselves. The user manual says never to use the Lumo+ on the eyes, the upper or lower eyelids, or skin inside the eye socket. On the skin just outside the socket, such as the crow's feet, keep to level 3 or below. For the eyelids, use the Venus.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Does the Lumo⁺ cause loss of volume in the face?

The fat loss you may have read about was reported with in-clinic RF microneedling, which delivers heat through needles below the skin (FDA safety communication, October 2025). The Lumo+ uses no needles and holds the skin at about 40 to 42°C. Stay within the usage limits and keep the handset moving.

Source: US FDA safety communication on RF microneedling; Lumo+ user manual. Reviewed November 2026

Was this helpful?

Can I use the Lumo⁺ after a facelift?

Only once you have fully healed and your surgeon has cleared you. Healing after a surgical facelift takes much longer than after a non-surgical lift, so ask the person who treated you when RF is appropriate.

Source: EvenSkyn guidance. Reviewed November 2026

Was this helpful?

Can I use the Lumo⁺ if I've had a metal hip implant or hip replacement?

No. The Lumo+ user manual says it is not for people with metal implants anywhere in their body, and this FAQ follows the manual. If you have questions about your own situation, contact support@evenskyn.com before you use it.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Can I use the Lumo⁺ alongside in-clinic RF treatments?

Not at the same time. Clinic treatments deliver far more energy, and skin needs to heal fully in between. Stop the Lumo+ at least two weeks before a clinic session and wait at least four weeks afterwards, or longer if your provider advises.

Source: EvenSkyn guidance. Reviewed November 2026

Was this helpful?

Can the Lumo⁺ be used on every Fitzpatrick skin type?

Yes. The Lumo+ is designed for all skin tones: its RF warms the skin below the surface rather than targeting pigment, and EMS works on the muscles. Use it as directed and keep the handset moving.

Fitzpatrick skin type test

Source: Lumo+ user manual; EvenSkyn guidance. Reviewed November 2026

Was this helpful?

Can I use the Lumo⁺ after a chemical peel?

Wait at least 14 days, and longer until your skin has fully healed. Healing time depends on the strength of the peel, so check with the professional who did it.

Source: EvenSkyn guidance. Reviewed November 2026

Was this helpful?

I have metal implants or screws in my face. Can I use the Lumo⁺?

No. The user manual says the Lumo+ is not for people with metal implants in their body. RF can heat metal, and the EMS current can travel through it. If you have questions about your own situation, contact support@evenskyn.com.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Can I use the Lumo⁺ with Botox or dermal fillers?

Yes, after a wait. Leave at least two weeks after Botox or hyaluronic acid filler before using the Lumo+ over the treated area, and longer if your injector advises. For other filler types, ask your injector first. A small trial of in-clinic RF straight after hyaluronic acid filler found no loss of effect, but no study has tested at-home devices.

Fillers: the full answer

Source: Goldman MP, Alster TS, Weiss R. Dermatologic Surgery 2007; conservative EvenSkyn guidance. Reviewed November 2026

Was this helpful?

Results

Will the EMS mode make my facial muscles more prominent?

No. The EMS (Massaging) mode makes facial muscles contract and release in a steady rhythm, for the look of a more toned jawline and neck. It isn't designed to build bulk. Never use it over the thyroid or Adam's apple.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

How long does it take to see results from the Lumo⁺?

Plan on at least 8 to 12 weeks of regular use within the limits before you judge it. RF works gradually, so changes in the look of firmness and fine lines build over months. Results vary with age, genetics and skin history. A photo once a week in the same light is the best way to track them.

Source: EvenSkyn Skin Science Desk. Reviewed November 2026

Was this helpful?

Can the Lumo⁺ be used on a double chin?

It depends on the cause. If loose skin along the jaw and neck is behind it, the Lumo+ can help the look of firmer skin there, as far as your skin's elasticity allows. If the double chin comes from fat, you won't see a change, because the Lumo+ doesn't reduce fat.

Source: EvenSkyn guidance. Reviewed November 2026

Was this helpful?

Care and troubleshooting

How do I charge the Lumo⁺, and how long does it take?

Set the Lumo+ on its charging base and plug in the adapter from the box. A full charge takes about 2 hours. Use only the supplied adapter, which accepts 100 to 240 volts, and make sure the handset and adapter are dry before you plug them in.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

My Lumo⁺ won't charge or hold a charge. What should I do?

Stop using it and contact us at support@evenskyn.com or +1 (888) 999-1946 with your order number. Don't open the handset or try a different charger. A battery or charging fault caused by a defect is repaired or replaced under the two-year warranty.

Source: Lumo+ user manual; warranty page. Reviewed November 2026

Was this helpful?

I can't feel any heat while using the Lumo⁺. Is this normal?

Yes. Most people feel gentle warmth or very little during RF. After a brief warm-up, a sensor in the head holds the skin at about 40 to 42°C, which is warm rather than hot. If it ever feels hot, stop and contact us.

Source: Lumo+ user manual; Lumo+ product page. Reviewed November 2026

Was this helpful?

What can I do if the Lumo⁺ feels too strong on my face?

Lower the level, starting from level 1. Use less gel, or switch to water or a lighter water-based gel, because a highly conductive gel makes EMS feel stronger. Spend less time in the Massaging mode, and stop if it stays uncomfortable.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Why is my eye or mouth twitching after using the Lumo⁺?

Mild twitching in the Massaging (EMS) mode is normal, because the mode works by making muscles contract. It depends on your sensitivity and the gel you use. Lower the level, use less gel or shorten the EMS part of your session. If twitching continues after you stop, contact us.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

How do I clean the Lumo⁺?

Power it off and unplug the adapter first. Wipe the head and magnetic ring after each use with a dry or lightly damp cotton pad or soft cloth, removing any gel, oil or moisturiser. Wipe the adapter only with a dry cloth, and let everything dry fully before charging.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Is the Lumo⁺ waterproof?

It is rated IP65, so it handles splashes and a damp face, but don't submerge it or leave it in water. Never charge it while it is wet.

Source: Lumo+ user manual. Reviewed November 2026

Was this helpful?

Choosing

How does the Lumo⁺ compare to Morpheus8?

They are different treatments. Morpheus8 delivers RF through microneedles in a clinic. The Lumo+ is an at-home RF device with no needles, so it works at much lower energy. It isn't a substitute and results aren't equivalent. Stop the Lumo+ two weeks before a Morpheus8 session and wait at least four weeks after.

Source: EvenSkyn guidance; US FDA safety communication on RF microneedling. Reviewed November 2026

Was this helpful?

What's the difference between the Lumo⁺ and other at-home RF devices?

The Lumo+ combines 1 MHz bipolar RF with EMS, red and blue LED and a cooling mode in one handset, and we publish its frequency, current, wavelengths, temperature and session protocol. Our device spec register compares what other brands publish about their devices.

The at-home device spec register

Source: Device spec register. Reviewed November 2026

Was this helpful?

Specs and science

What safety features and specifications does the Lumo⁺ have?

The Lumo+ runs 1 MHz bipolar RF with sensor-controlled heating, EMS at 3 to 15 mA, and red (623 nm) and blue (465 nm) LED. Every mode stops on its own timer, the head is 316 stainless steel with titanium electrodes, and it is rated IP65 for splashes. For certificates, contact support@evenskyn.com.

The at-home device spec register

Source: Lumo+ user manual; device spec register. Reviewed November 2026

Was this helpful?

What current does the Lumo⁺ EMS mode run at?

EMS is measured in milliamps, not microamps. The Lumo+ EMS runs from 3 to 15 mA across its five levels, far above a microcurrent device, which is why it is EMS. Start at level 1 and step up only while it stays comfortable.

Source: Device spec register; Lumo+ product page. Reviewed November 2026

Was this helpful?

Warranty and returns

What does the Lumo⁺ two-year warranty cover?

Defects in materials and workmanship for two years from the date of purchase by the original buyer, including a battery or charging fault caused by a defect. We repair or replace the device. It doesn't cover damage from misuse or from use that goes against the user manual.

Warranty information

Source: Warranty page. Reviewed November 2026

Was this helpful?

General information from the user manual and our policies, not medical advice. If you have a medical condition, take medication or are unsure whether this device suits you, ask your doctor before use. Where this page and a policy differ, the policy applies.

Still have a question?

Write to us and a real person on our team will reply. Include your order number if your question is about an order.

VIP early accessBlack Friday, answered

40% off sitewide through Cyber Monday, Nov 30, 11:59 PM ET.

How do I get the 40% off?

It's automatic. Add anything to your cart and code BLACK40 goes on for you, so you'll see 40% off every item before you pay. If you ever don't see it, type BLACK40 in the discount box at checkout.

Will the price change before Cyber Monday?

It won't go up. This is our Black Friday price through Cyber Monday, Nov 30 at 11:59 PM ET. The one change we've made is a better one: since November 6, MicroInfuser kits cost less each when you buy 2 or 3. We may also add complimentary extras along the way, like conduction gel or MicroInfuser samples.

Is there a deal on more than one MicroInfuser kit?

Yes. Buy 2 kits and each one costs less than a single kit, and buy 3 or more and each costs less again. Three kits cover about six months of sessions. The saving comes off automatically at checkout, in place of BLACK40, and if your cart has other items too, checkout uses whichever saves you more.

Can I use a different code?

Yes, but only one code works per order, so codes don't stack. If you use another code, it replaces BLACK40, and for almost every order BLACK40 saves you the most.

Do the sets get 40% off too?

Yes. BLACK40 takes 40% off every item, sets included, and our sets still cost less than buying each piece on its own.

What if it isn't right for me?

The usual terms apply to sale orders. Devices come with our 60-day money-back guarantee for US and Canadian residents; return shipping is on you, or we deduct up to $20 if you use our prepaid label. The MicroInfuser kit has a 60-day money-back guarantee on unused treatments. Lumo⁺ keeps its 2-year warranty and our other devices their 1-year warranty.

Is shipping free?

Yes, in the US and Canada.

Every Black Friday price, in one place
Sale dates, prices and terms